Hot Tub Disposal

Guide · Homeowners · 4 min read · Updated 16 November 2026

How to Disconnect a Hot Tub: Plug-and-Play vs Hardwired

Short answer

A plug-and-play hot tub is disconnected simply by switching off and unplugging it from its RCD-protected socket. A hardwired hot tub is part of the fixed electrical installation, usually on its own circuit with an outdoor isolator, so the supply should be isolated, disconnected and made safe by a competent electrician in line with BS 7671 before the tub is moved.

A hot tub in snow

Which type do you have?

Hot tubs fall into two broad electrical types. Plug-and-play tubs run from an ordinary 13 amp socket, usually through a lead with a built-in RCD plug. They tend to be smaller or lower-powered, and the heater often switches off while the jets are running. Hardwired tubs are connected to a dedicated circuit from the consumer unit, often 32 amps or more, through an outdoor isolator switch or RCD unit mounted near the tub. If you are not sure, look at where the cable goes. A plug and socket means plug-and-play. A cable running into a weatherproof isolator box on a wall or post, and from there into the tub cabinet, means hardwired. Older installations are not always tidy, so look for any extra cables, such as lighting or a separate supply for a gazebo, that may also need making safe before the tub is moved.

FeaturePlug-and-playHardwired
Supply13 amp socketDedicated circuit from the consumer unit
ProtectionRCD plug or socketRCD in consumer unit or outdoor unit
DisconnectionUnplugElectrician isolates and makes safe
What is left behindNothingCable and isolator, made safe or removed

Disconnecting a plug-and-play tub

This is straightforward. Switch the tub off at its control panel, then at the socket, and unplug it. If the socket is outdoors, check that its weatherproof cover closes properly once the plug is removed. Coil the lead and tuck it into the cabinet or tie it to the tub so it does not get caught during removal. Always switch off before draining, and never handle plugs or sockets with wet hands. If the outdoor socket was installed specially for the hot tub and you will not need it again, you may want an electrician to remove or blank it later. Even with a plug-and-play tub, check the lead and plug for damage before handling, particularly if the tub has been outdoors for years. A cracked plug or perished lead should be left switched off at the socket and handled with care.

Disconnecting a hardwired tub

Hardwired hot tubs are part of the fixed electrical installation, and work on them should be carried out by a competent electrician in line with BS 7671, the wiring regulations. Switching off the isolator stops the tub from running, but it does not make the supply cable safe to cut or disconnect. The electrician will isolate the circuit at the consumer unit, prove it dead, disconnect the cable from the tub's control pack and terminate the supply safely. Depending on your plans, the electrician can leave a properly terminated isolator for a future tub, or remove the circuit back to the consumer unit.

  • Do not cut or unscrew a hardwired supply cable yourself
  • Switching off the isolator is not the same as making the cable safe
  • Ask the electrician to label the circuit as disconnected at the consumer unit
  • Keep any certificate or note the electrician gives you

Why it matters

Hot tubs combine water and high-current electricity outdoors, which is a dangerous mix if handled carelessly. A supply cable cut while live, or left with exposed ends in a garden, is a serious shock hazard to anyone who touches it later, including children and pets. Removal crews will not move a hardwired tub until they are satisfied the supply has been made safe, so arranging this in advance avoids a wasted visit. Disconnection is usually quick for an electrician, so it is often easy to schedule for the day before removal. It is also worth checking the condition of the outdoor isolator itself. Cracked covers, water ingress and corroded terminals are common on older installations and are best dealt with at the same visit.

Timing the disconnection

The most efficient order is to stop dosing chemicals, switch off and drain the tub, then have the electrician disconnect it, and finally have it removed. If the tub is being replaced rather than just removed, talk to your new tub supplier about whether the existing supply is suitable. A larger replacement may need a higher-rated circuit, while a plug-and-play replacement may not need the hardwired supply at all. Tell us at the quote stage whether your tub is hardwired, and whether disconnection has been arranged, so we can plan the visit correctly. If you rent your home or the tub was installed by a previous owner, check who owns it and whether the supply was installed properly. Landlords should arrange disconnection through their own electrician, and tenants should not remove a tub that belongs to the property without written permission.

Inflatable and wooden tubs

Inflatable hot tubs are almost always plug-and-play, with the pump and heater unit running from a socket. Unplug the unit, drain the liner and deflate it. The pump unit is electrical waste under the WEEE Regulations 2013 and should be recycled rather than put in a household bin. Wood-fired barrel tubs have no electrics, but their stoves, flues and any ash need clearing safely. Wooden tubs with electric heaters follow the same rules as other tubs, depending on whether they plug in or are hardwired.

Questions people also ask

Can I disconnect a hardwired hot tub myself?

It is not recommended. Hardwired tubs are part of the fixed electrical installation, and disconnection should be done by a competent electrician in line with BS 7671. Switching off the isolator does not make the cable safe to cut. A wrongly terminated supply left in a garden is a serious shock risk.

Will you disconnect my hot tub as part of removal?

Plug-and-play tubs are simply unplugged on the day. For hardwired tubs, the supply needs to be made safe by a competent electrician, which we can arrange or you can book yourself before removal day. Tell us which type you have when requesting a quote.

What happens to the outdoor isolator after removal?

That depends on your plans. An electrician can leave the isolator in place with the supply safely terminated for a future tub, or remove the circuit and isolator altogether. Either way, ask them to label the circuit at the consumer unit so its status is clear.

Written and checked by the Hot Tub Disposal team. Read our editorial policy.

Get a free hot tub disposal quote

Tell us what you need and we'll come back with a clear price.

Request a quote