Guide · Homeowners · 4 min read · Updated 16 November 2026
How to Drain a Hot Tub Safely Before Removal
Short answer
To drain a hot tub before removal, stop adding chlorine or bromine a few days beforehand so levels fall, switch off and isolate the power, then empty the tub through its drain valve or with a submersible pump. Send the water to a foul drain, such as an outside gully connected to the sewer, not a surface water drain. Finish by sponging out the footwell and removing the filters.
Before you start
A typical hot tub holds somewhere around 1,000 to 1,500 litres of water, so draining takes time. With a garden hose on the built-in drain valve it can take several hours. A submersible pump is much faster. Plan to drain the tub the day before removal or a day or two earlier, so it has time to dry out a little. Stop adding chlorine or bromine a few days before you drain. Sanitiser levels fall naturally over time, especially with the cover off in daylight, and lower levels are better for wherever the water ends up. Do not add other chemicals to try to speed this up unless you know what you are doing. Check the weather too. Draining in heavy rain is miserable and makes it harder to see where the water is going. A dry day also helps the shell and footwell dry before the crew arrive.
Where hot tub water can go
This is the part most people get wrong. Many homes have two drainage systems. The foul system carries waste from toilets, sinks and showers to the sewage works for treatment. The surface water system takes rain from roofs and driveways and often discharges straight into a stream, river or soakaway. Hot tub water containing chlorine or bromine should go to the foul system, not the surface water system, because sanitiser can harm wildlife in watercourses. Not sure which is which? An outside gully that takes water from a kitchen sink or washing machine is usually foul. Gullies under rainwater downpipes are often surface water, though in some older properties they join the foul system.
| Destination | Suitable? | Why |
|---|---|---|
| Foul drain or gully connected to the sewer | Yes | Water goes to the sewage works for treatment |
| Inside toilet or sink, in small amounts | Yes | Also foul, but slow for large volumes |
| Surface water drain or road gully | No | Often discharges directly to rivers and streams |
| Lawn or flower beds | Not with sanitiser | Chlorine or bromine can harm plants and soil life |
| Ditch, stream or pond | No | Direct pollution of a watercourse |
Step-by-step draining
Work methodically and keep electricity and water apart. The steps below suit most hard-shell tubs. Check your tub's manual for the location of its drain valve and any specific instructions. Keep the cover nearby but off the tub while draining, and keep children and pets away from the open tub and the hose run. Check the hose end from time to time to make sure it has not slipped out of the drain.
- Switch off the tub at its isolator or unplug it before any water is removed
- Remove the cover and take out the filters for cleaning or disposal
- Attach a hose to the drain valve, or lower a submersible pump into the footwell
- Run the hose to a foul drain and check it stays in place
- Open the valve or start the pump and keep an eye on it throughout
- Use a wet vacuum or sponge to remove the last water from the footwell and seats
- Leave the cover off for a few hours so the shell can dry
Using a submersible pump
A submersible pump drains a tub in a fraction of the time a gravity drain takes. Place it in the deepest part of the footwell, connect a layflat or garden hose and run it to the foul drain. The pump must be plugged into a socket protected by an RCD, with the cable and plug kept well away from the water. Never leave a pump running unattended for long, because most should not run dry. Pumps can be hired cheaply or bought from DIY stores. If you would rather not deal with it, our draining service starts from £50 and is carried out before removal on the same visit.
Problems you may run into
Old tubs often have seized or broken drain valves. If the valve will not open, use a pump instead and do not force it. Some tubs have water trapped in pipework and jets after the main drain, which runs out when the tub is tipped, so expect a little more water on removal day. If the tub has been neglected and the water is green or foul, it can still go to the foul drain, but wear gloves and avoid splashing. Very cold weather adds a complication. If a tub has been left full and switched off in winter, ice can damage pipework, though this matters less if the tub is being removed for disposal.
If water starts backing up from the drain, stop the pump or close the valve and let the drain catch up. Older drains and gullies can struggle with a sustained flow, and an overflowing gully on a patio is easier to prevent than to clean up. Running the pump in bursts gives a slow drain time to clear between runs.
After draining
Once the tub is empty, leave the power isolated. If it is a plug-and-play model, unplug it and coil the lead. If it is hardwired, have a competent electrician disconnect and make safe the supply before removal day, in line with BS 7671. Clear the route to the gate, and put the filters and any chemicals somewhere safe. Unused hot tub chemicals should not be poured down the drain; follow the product label or take them to your council's household hazardous waste facility if it has one.
Questions people also ask
Can I drain my hot tub onto the lawn?
Not if the water still contains chlorine or bromine, which can damage grass, plants and soil life. Stop dosing several days beforehand and, ideally, send the water to a foul drain connected to the sewer. Surface water drains are also unsuitable, as they often flow straight into streams and rivers.
How long does it take to drain a hot tub?
Using the built-in drain valve and a garden hose, draining usually takes several hours, depending on the size of the tub and the drop to the drain. A submersible pump empties a typical tub much faster, often in well under an hour. Allow extra time to sponge out the footwell.
Do I need to remove the filters before removal?
It helps. Filters are usually easy to lift out, and removing them lets the last water drain from the filter housing. They can go with the tub for disposal or in your general waste, depending on their type. Keep any spare filters if you plan to buy another tub of the same model.
Written and checked by the Hot Tub Disposal team. Read our editorial policy.
More guides
How Much Does Hot Tub Disposal Cost in the UK?
In the UK, removing a drained hard-shell hot tub in one piece typically costs £250–£400, provided there is a gate or path about a metre wide. If the…
Will My Hot Tub Fit Through the Gate? Whole vs Cut-Up Removal
Most hot tubs leave a garden tipped on their side, so the route needs to be slightly wider than the tub's depth, usually around a metre, all the way…
How to Disconnect a Hot Tub: Plug-and-Play vs Hardwired
A plug-and-play hot tub is disconnected simply by switching off and unplugging it from its RCD-protected socket. A hardwired hot tub is part of the…
What to Do With an Old Hot Tub: Sell, Give Away or Dispose
A working hard-shell hot tub from a known brand, under ten years old and in good condition, can often be sold. Older or faulty tubs may be given away…
Inherited a Hot Tub When You Moved? Your Options Explained
If you have moved into a house with a hot tub you do not want, first check whether it works, how old it is and what condition the cover and electrics…
After Hot Tub Removal: The Base, Electrics and What Comes Next
After a hot tub is removed, you are left with a base, usually concrete, paving or decking, and an electrical supply. Have an electrician make the…
Get a free hot tub disposal quote
Tell us what you need and we'll come back with a clear price.
Request a quote